How Arbitrary IPv4 Ranges Decompose into Minimal CIDR Prefix Blocks
Cloud firewalls, AWS Security Groups, BGP prefix-lists, Linux nftables/iptables, and Nginx allow/deny directives only accept power-of-two aligned CIDR blocks—never arbitrary start-to-end hyphenated IP spans such as 192.168.1.10 – 192.168.1.50. Because CIDR blocks must align on exact 2^k bit boundaries (where cur % 2^k === 0 and cur + 2^k - 1 <= end), a single non-aligned IP range often requires multiple adjacent CIDR prefixes to cover those exact addresses without leaking access to neighboring hosts.
This pre-configured IP Range to CIDR Converter runs greedy 32-bit bitwise interval decomposition in your browser, outputting both the exact zero-overreach CIDR block list (one per line, ready to paste into Terraform or WAF rules) and the smallest single enclosing supernet CIDR.
- Zero-Overreach Exact CIDR List: Covers 100% of IPs between Start IP and End IP inclusive while excluding every single IP outside the range—critical for security allowlists.
- Smallest Single Enclosing Supernet: Computes the longest shared MSB prefix of Start IP XOR End IP and reports the exact count of extra IPs if you summarize into one rule.
- Dotted-Decimal Subnet Mask to CIDR Support: Switch to CIDR / Mask → IP Range mode above and type 10.0.0.1/255.255.255.240 to convert legacy dotted netmasks directly to /28.
Worked Example: Converting 192.168.1.10 – 192.168.1.20 into 4 Exact CIDRs
Suppose a vendor gives you an IPv4 allowlist span of 192.168.1.10 through 192.168.1.20 (11 total IP addresses). Starting at .10 (binary ...00001010), the trailing zero count is 1, so the largest aligned block starting at .10 is a /31 (2 IPs: .10–.11). Next, .12 (...00001100) has 2 trailing zeros and .12 + 3 = .15 <= .20, yielding 192.168.1.12/30 (4 IPs: .12–.15). Next, .16 (...00010000) could align up to a /28 (.16–.31), which exceeds .20, so the algorithm steps down to 192.168.1.16/30 (4 IPs: .16–.19), finishing with 192.168.1.20/32 (1 IP).
Summing 2 + 4 + 4 + 1 = 11 IPs proves exact coverage in 4 minimal rules—whereas using the single enclosing supernet 192.168.1.0/27 (32 IPs) would accidentally expose 21 unauthorized neighboring hosts.
Practical Real-World Use Cases
Network security, SRE, and DevOps teams convert IP ranges into CIDR blocks across daily firewall and routing tasks:
- Converting Vendor & Payment-Gateway IP Spans for AWS Security Groups: Translate legacy "Start IP – End IP" partner webhook documentation into exact /29, /30, and /32 ingress rules in Terraform or AWS EC2.
- Whois / RIR NetRange Block Auditing (ARIN, RIPE, APNIC): Paste NetRange start and end addresses from whois lookups to generate exact CIDR blocks for Cloudflare WAF, fail2ban, or GeoIP blocks.
- DHCP Pool Exclusion & Cisco ACL Wildcard Sizing: Verify whether a static server reservation range aligns cleanly on a single CIDR boundary or splits across multiple subnet masks.
Frequently Asked Questions
Why does converting one IP range sometimes produce multiple CIDR blocks?
Every CIDR prefix /p represents a block of 2^(32-p) addresses whose starting IP must be evenly divisible by that block size. Whenever a start or end IP does not land on a power-of-two boundary, multiple smaller aligned CIDR blocks are mathematically required to cover the exact range without spilling into adjacent IPs.
How do I convert a subnet mask like 255.255.255.240 to CIDR notation?
Count the contiguous leading 1-bits across all four octets (255 = 8 bits, 240 = 11110000 = 4 bits, so 8 + 8 + 8 + 4 = /28), or switch to CIDR / Mask mode above and enter IP/255.255.255.240 directly.